Greatly Increase Your Driving Range With This 65-Gallon Fuel Tank Which Is Easy To Install
One thing all pickup drivers have in common is the feeling of rising anxiety as they watch their fuel gauge fall below the quarter-tank mark and rapidly plummet closer to “E.” That tension is amplified when you are driving across unfamiliar terrain and are not sure where the next gas station might be. Or perhaps it’s late at night when smaller stations are closed and running out of fuel becomes a distinct possibility. In these scenarios, having an extra 10, 15, or 20 gallons of fuel in the tank could save you some stress.
Maybe you are an RVer, rancher, farmer, construction worker, or a “hot-shot” commercial transport driver towing trailers with a heavy-duty diesel pickup. If you don’t like making frequent pit stops for fuel as you go about your daily tasks, an extended fuel tank could be the answer. The more miles you can put under the wheels between fill-ups, the better.
That’s where having a higher-capacity tank, like the TITAN Gen6 XXL fuel tank, in your diesel pickup can save you both time and money.
TITAN Gen6 XXL Fuel Tank
TITAN Fuel Tanks, based in Idaho Falls, Idaho, has been offering a solution to extend the driving range of pickups for decades with their wide selection of high-capacity fuel tanks for both gas and diesel applications.
Their newest offering is the Generation 6 Extended Capacity Replacement Tank (#7020317) for 2017-newer, long-bed Ford Super Duty Crew Cab Diesel pickups. The TITAN Gen6 XXL fuel tank, which costs about $1,300, depending on where you buy it, increases the fuel capacity to 65-gallons, which is 17 gallons more than Ford’s 48-gallon tank.
That extra fuel capacity could extend a newer 6.7L Power Stroke’s range by more than 300 miles driving unloaded, and around 200 miles when towing a heavy trailer. This extra-capacity, extra-heavy-duty mid-ship replacement fuel tank is a direct bolt-in replacement for 2017-2021 FORD F250, F350, and F450 pickups with Crew Cabs, 8 ft beds, and Power Stroke engines. It comes with a new front strap, special crossmember bracket, and sending unit seal.
A Better Plastic Fuel Tank
What makes the DOT-compliant, C.A.R.B-certified TITAN Fuel Tanks special is the “military-grade” plastic construction. While OEMs such as Ford use linear polyethylene, TITAN goes a step further in strength and durability by using cross-linked high-density polyethylene (XLHDPE) for their tanks. It’s also has a ¼-inch thick wall, so it’d take a lot to puncture it.
“Sheer strength is the biggest difference,” said Mike Deford, TITAN’s marketing manager. “The cross-linked polymer is leaps and bounds ahead of linear polyethylene or metal offerings. It doesn’t rust or corrode, nor does it crack or crush when hit. It also doesn’t conduct cold or hot temperatures as poorly as metal does, so everything inside stays fluid, as it should be.”
What the new tank doesn’t come with is a replacement skid plate. So we suggest ordering one as the OEM skid plate will not fit the new tank, and the TITAN fuel tank hangs about 2 inches lower than the OEM one.
Filling The Empty Spaces
Side by side. The 65-gallon TITAN Gen6 XXL fuel tank (foreground) is slightly larger all around than the 48-gallon factory unit.
How does TITAN get the extra fuel capacity? Simple. Fill in the open spaces around the OEM tank design. For example, TITAN’s XXL tank for the Long-Bed Crew Cab F-350 4×4 fills in most of the void between the OEM tank and the transfer case. The aftermarket tank is also 1.75 inches deeper and slightly wider than the 48-gallon factory tank.
An inch here, a foot there over 6-plus feet, and suddenly the volume is there to hold 17 more gallons of fuel. That higher capacity also means that you’ll need to have the DIC re-calibrated at your local Ford dealer after install so it reads correctly.
Easy to Install With The Right Tools
The TITAN website claims they make every effort to make installation as simple as possible to swap the Gen6 XXL Fuel Tank in place of your original tank. We found that to be true. Not only does TITAN provide detailed instructions, but they also have video instructions on their website.
Generally speaking, installation entails removing your pickup’s stock tank, moving the in-tank sending unit and external water separator, connecting fuel lines over to the TITAN tank, installing a new forward tank mount, and bolting in the new tank. There are no modifications needed.
Installation time for a 2019 F-350 Dually that we installed TITAN’s XXL long bed 65-gallon fuel tank on took us approximately 4 hours using a 4-post lift and hydraulic transmission jack at Mobile Diesel Service’s shop in Sutherlin, Oregon.
One other installation note: it saves a lot of time and headache if you run the OEM fuel tank as low on fuel as possible before making this swap. Diesel weighs about 7 pounds per gallon, so the less fuel in the tank, the easier it is to handle and remove it from under your truck.
So, get to it — you’re well on your way to enjoying fewer pit stops on your drive!
How To Install a TITAN Gen6 XXL Fuel Tank
Step 1: Swapping out the OEM Ford fuel tank begins by removing the factory skid plate.
Step 2: Disconnect the fuel lines from the tank to the engine.
Step 3: The filler hose and vent also need to be removed to drop the OEM tank.
Step 4: Ford uses a strong thread locker on the tank mounting bolts. Using an air impact gun will most likely break the clips holding the nuts.
Step 5: Broken clips can be removed with a cut-off wheel to get bolts out.
Step 6: Before removing the OEM fuel tank, removed the bolt that holds the water separator to its tank mounting bracket. Use a T-27 Torx bit.
Step 7: A hydraulic transmission jack and a helper make removal of the factory tank an easy process.
Step 8: We removed the lock ring holding the sending unit in the OEM Ford tank using a hammer and flat drift.
Step 9: The fuel lines need to be popped out of the factory brackets so new lines can be moved together for the TITAN tank.
Step 11: We coated the new sending unit sealing o-ring with white lithium grease to ensure a leak-free seal.
Step 12: The change-over of the OEM fuel tank components is a no-drama event. Lift and set into place in the TITAN tank.
Step 13: It takes a few good raps with a hammer to get the sealing ring to lock into place. Making sure this ring locks is critical in ensuring there are no fuel leaks.
Step 14: Re-installing the water separator bracket retaining screw is important — and easiest done when the new tank is being prepped.
Step 15: The TITAN XXL kit comes with a new front mounting plate, threaded rod, and hardware. Install before lifting the tank into place.
Step 16: Forward tank hanger attaches to the cross member just aft of the transfer case.
Step 17: Higher-capacity TITAN Gen6 XXL fuel tank fits easily back into place under our 2019 F-350 Super Duty 4×4.
Step 18: A hole is molded in the big tank where the threaded rod can protrude to catch the new TITAN-supplied strap.
Notes: We replaced the broken OEM tank strap bolts and clips with comparable size Grade 5 bolts and locknuts. The TITAN Gen6 XXL fuel tank hangs about 2 inches lower than the factory fuel tank. We recommend installing an aftermarket skid plate if your truck is going to see any off-pavement use. The OEM skid plate doesn’t fit the TITAN fuel tank.
RESOURCES:
TITAN Fuel Tanks: 208-522-1325
Mobile Diesel Service: 541-459-8939
Keyword: Stretch Your Mileage With The TITAN Gen6 XXL Fuel Tank